Saltwater Master Liquid Test Kit

Directions- read thoroughly before testing. Do not allow Test Solutions to get into aquarium. To remove childproof safety caps: With one hand, push red tab left will thumb while unscrewing cap with free hand.High Range pH Test Fill a clean test tube with 5 ml of water to be tested (to the line on the tube). Add five drops of indicator solution, holding dropper bottle upside down in a completely vertical position to assure uniformity of drops.Cap the test tube and invert tube several times to mix solution. Do not hold finger over open end of tube, as this may affect the test results. Determine the pH reading by matching the color of the solution against those on the High Range pH color chart. The tube should be viewed against the white area beside the color chart. Color comparisons are best made in a well-lit area. The closest match indicates the pH of the water sample. Rinse the test tube with clean water after each use.Recommended pH levels: Saltwater: a pH of 8.2 is ideal for saltwater fish and invertebrates. To automatically set the pH at 8.2 use Aquarium Pharmaceuticals proper pH 8.2 for saltwater aquariums. Proper pH 8.2 is carbonate buffer which automatically adjusts and holds the pH at 8.2. Freshwater: a pH of 7.5 is ideal for most live-bearing fish, such as mollies and swordtails. Goldfish will also thrive at a pH 7.5. To raise or lower the pH of freshwater aquarium, use Aquarium Pharmaceuticals pH up or ph down, following the directions on the container. Proper pH 7.5 may be used automatically adjust and hold pH at 7.5. Proper pH 8.2 may be used in African cichlid aquariums.Frequency of Testing: The pH should be tested weekly, since natural materials in the aquarium (such as fish waste and decaying food) can cause pH changes. The minimum pH reading for this kit is 7.4 and the maximum is 8.8. Under the extreme water conditions, reading below the minimum will read 7.4 and above the maximum will read 8.8. pH adjustments outside the range of this kit will not show any changes until the pH of the aquarium water is within the range of this kit. Ammonia Test Fill a clean test tube with 5 ml of water to be tested (to the line on the tube). Add 8 drops from Ammonia Test Solution Bottle # 1, holding the dropper bottle upside down in a completely vertical position to assure uniformity of drops added to the water sample.Add 8 drops from Ammonia Test Solution Bottle # 2, holding the dropper bottle upside down in a completely vertical position to assure uniformity of drops added to the water sample.Cap the test tube and shake vigorously for 5 seconds. Do not hold finger over the open end of the tube, as this may affect the test results.Wait 5 minutes for the color to develop. Read the test results by matching the test solution against the Ammonia Test Color Chart. The tube should be viewed against the white area beside the color chart. Color comparisons are best made in a well-lit area. The closest match indicates the ppm (mg/L) of ammonia in the water sample. Rinse the test tube with clean water after each use. What the Test Results Mean: In a new freshwater or saltwater aquarium, the ammonia level may surge to 6 ppm (mg/L) or more, then fall rapidly as the biological filter becomes established. This process may take several weeks, use Aquarium Pharmaceuticals StressZyme to speed up the development of the biological filter. In an established aquarium, the ammonia level should always remain at 0 ppm (mg/L). The presence of ammonia indicates possible over-feeding, too many fish or inadequate biological filtration. The ammonia level is not an indication of the nitrite levels; nitrite is another toxic waste material that must be tested separately. Monitoring Ammonia Levels: Regular testing is necessary to make sure the ammonia level is safe. Aquarium water should be tested for ammonia every other day when the aquarium is first set up, and once a week after the biological filter has been established (in about 4 to 6 weeks). Detoxifying Ammonia Using Ammo-Lock in Freshwater & Saltwater Aquariums: To detoxify ammonia, use Aquarium Pharmaceuticals Ammo-Lock to instantly lock up ammonia. Ammo-Lock does not remove ammonia, it simply converts toxic ammonia to a non-toxic form. Ammonia test kits will still test positive for ammonia, even though it is non-toxic. The biological filter will then consume the non-toxic ammonia, converting it to nitrite and then to nitrate. Water Changes: Changing 25% of the aquarium water will reduce the ammonia level. In an emergency, a daily water change may be required over several days. Be sure to use a water conditioner like Stress Coat or Ammo-Lock, when adding tap water back into the aquarium. Danger: harmful xn, corrosive c: Bottle # 2 contains sodium hydroxide and sodium hypochlorite. Causes severe burns. Contact with acids liberates toxic gas. Toxic inhalation, in contact with skin and if swallowed. Danger of cumulative effects. Keep locked up and out of reach of children. Keep away from food, drink and animal feeding stuffs. In case of contact with eyes, rinse immediately with plenty of water (at least 15 minutes) and seek medical advice immediately. After contact with skin, wash immediately with plenty of water. Remove contaminated clothing. Wear suitable gloves and eye/face protection. In case of accident or if you feel unwell, seek medical advice immediately (show label where possible). Do not mix with acidic materials. Nitrite TestFill a clean test tube with 5 ml of water to be tested (to the line on the tube). Add 5 drops of Nitrite Test Solution, holding dropper bottle upside down in a completely vertical position to assure uniformity of drops added to the the water sample.Cap the test tube and shake the tube for 5 seconds. Do not hold finger over the open end of the tube, as this may affect test results. Wait 5 minutes for the color to develop.Read the test results by matching color of the solution against those on the Nitrite Test Color Chart. The tube should be viewed against the white area beside the color chart. Color comparisons are best made in a well-lit area. The closest match indicates the ppm(mg/L) of nitrite in the water sample. Rinse the test tube with clean water after each use.What the Results Mean: In new freshwater and saltwater aquariums the nitrite level will gradually climb to 10 ppm(mg/L) or more. As the biological filter becomes established (in 4 to 6 weeks), nitrite levels will drop to 0 ppm (mg/L) of nitrite in the water sample. The presence of nitrite indicates possible over-feeding, too many fish or inadequate biological filtration. The nitrite level is not an indication of the ammonia level; ammonia is another toxic waste material that must be tested separately.Monitoring Nitrite Levels: Regular testing for nitrite is an essential part of routine aquarium maintenance. Aquarium water should be tested for nitrite once a week to make sure the nitrite does not reach undesirable level. Reducing Nitrite in the Aquarium: Partial water changes will lower nitrite in a saltwater aquarium. Use Aquarium Pharmaceuticals StressZyme to help speed up the development of the biological filter. Nitrate Test Fill a clean test tube with 5 ml of water to be tested (to the line on the tube). Add 10 drops from Nitrate Test Solution Bottle # 1, holding dropper bottle upside down in a completely vertical position to assure uniformity of drops added to the water sample. Cap the test tube and invert tube several times to mix solution. Do not hold finger over the open end of the tube, as this may affect test results. Vigorously shake the Nitrate Test Solution Bottle # 2 for at least 30 seconds. This step is extremely important to insure accuracy of test results. N